- UID
- 30017
- 精华
- 积分
- 3886
- 胶币
- 个
- 胶分
- 点
- 技术指数
- 点
- 阅读权限
- 70
- 在线时间
- 小时
- 注册时间
- 2009-3-17
- 最后登录
- 1970-1-1
|
发表于 2009-4-24 17:22:19
|
显示全部楼层
ASTM D1330-85(2000) # M& I% F8 }) ?0 z* Y7 G
- j" ]6 E) {/ `7 w- x! \
, Z4 ?! i6 c7 O9 P
Historical Standard: ASTM D1330-85(2000) Standard Specification for Rubber Sheet Gaskets 1 _" V E! z" D& g6 u" a1 c
) p- Y; E" Q+ J; K5 I
; W4 f+ A' k. w0 dSUPERSEDED
, x- q- r( z; j/ Z m C- C8 B$ d( o2 Y5 P2 [, k' l
Buy Standard (PDF) 2 pages $ 37.20
# I* [2 l! c0 P% ^+ U1 S& g& `* l& E. F; j
Active(view current version of standard)
y" [6 ?- M& `8 N5 S: r; x9 J5 \* E6 ^( K& U8 f0 o" l! a0 u, ^
/ b6 S# V( W9 N6 t1 A. I0 R# y$ o
% }% R: B1 a% Q& I' n3 S
1. Scope
0 X6 [/ z+ S5 F- i! q, K8 Y2 C
, r; n' l( ~4 k) h3 A$ X6 c. W5 f. _4 }7 p& n9 x/ N& x: f
1.1 This specification covers gaskets cut from sheet rubber that are intended for general gasket applications on water, air, and low-pressure steam. They are not intended for use with oils and strong acids.
( R/ F2 c, G' @7 D P& n0 Y
, m& L: P. j: m# |; g, L1.2 The values stated in SI units are to be regarded as the standard. ' x8 ^( x* |8 h! D9 J
7 A/ H8 f( G# e" z0 K. J `
% A! S1 U, y! |; |3 V, ^) F- B1 e
2. Referenced Documents * s+ f- F2 U$ I! T5 v
6 Y) }' Z8 Q2 v
! K3 f% F- Y& e+ N, d. OD1415 Test Method for Rubber Property-International Hardness
* R- k5 p0 V i- HD2240 Test Method for Rubber Property-Durometer Hardness ' c- H; b( I' _) _' h% n& d
D3182 Practice for Rubber-Materials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets
+ g0 K5 d2 F" a; p: CD3183 Practice for Rubber-Preparation of Pieces for Test Purposes From Products
& l% _2 ^/ ]: W* H# B& r+ y5 WD395 Test Methods for Rubber Property-Compression Set , ~& H; ]4 {6 H' `7 g
D412 Test Methods for Vulcanized Rubber and Thermoplastic Elastomers-Tension
& W8 R+ i6 j" a5 x1 ND573 Test Method for Rubber-Deterioration in an Air Oven
3 d/ }1 ^; ]) @0 p% O4 yD865 Test Method for Rubber-Deterioration by Heating in Air (Test Tube Enclosure) |
|